How to reset check engine light on polaris ranger

How to reset check engine light on polaris ranger

To log in, download updates and learn more, visit the Ride Command website. Require Passcode to Start Engine By activating the passcode protection, you now have control of who operates the vehicle and when the vehicle is operated.

When enabled, the passcode must be entered before the engine starts. If your child is out riding, a restart option allows you to restart the vehicle within a pre-determined time limit before having to re-enter the passcode. When this option is enabled, the engine will not be allowed to start without entering the passcode on the display in the vehicle.

Restart Lock Delay If a passcode is required to start the engine, a restart lock delay also can be enabled. A restart lock delay of 10 minutes will allow the engine to be restarted without a passcode for 10 minutes since the time the engine stopped. This setting will set a maximum vehicle speed and will limit override any speed setting for geofences if the geofence speed limit is higher. Adding A Geofence Keep your kids in safe parameters by quickly setting and controlling ride boundaries.

A geofence is a virtual "fence" that allows you to specify vehicle speeds for inside and outside the area created by a geofence. The inside speed and outside speed can be set individually in any values from 10 to 29 miles per hour. Your comments are important for us. We will review your suggestions to see how we can improve this article. Skip to content Skip to navigation Skip to footer. Open the Ride Command App. Put the vehicle into accessory position by turning the key to the first key position.

If you have no vehicles in your Garage yet, tap "Add a Vehicle. It will show up in the list once it is found. Give your vehicle a name and other optional info shown on your app screen. Tap "Done. Tap on "Create Password. Type a four-digit password. Confirm your password by typing it again on the next screen.

Enter the existing PIN. Reference the above image. Press the MODE button to set the second digit and move on to the third digit. Press the MODE button to set the third digit and move on to the fourth digit. Press the MODE button to set the fourth digit and exit. Do not press any button for 10 seconds, which will exit out of the Youth Menu. Tap on "Restart Lock Delay. An option will appear below to set the value. Tap on this option and select the maximum vehicle speed. Move the map and zoom in or out to find where your first point will be.

Tap the map to add your first point. Move and zoom the map as needed, and continue tapping points to draw your geofence.During these challenging times, we guarantee we will work tirelessly to support you.

How to Reset the Service Wrench on a Polaris Sportsman

We will continue to give you accurate and timely information throughout the crisis, and we will deliver on our mission — to help everyone in the world learn how to do anything — no matter what.

Thank you to our community and to all of our readers who are working to aid others in this time of crisis, and to all of those who are making personal sacrifices for the good of their communities. We will get through this together. Your check engine light typically comes on when there is a problem with your emission control system or another computer-controlled system in your vehicle. The light generates a code that can help you narrow down the problem so you can get it fixed.

You may also need to manually reset the light after making repairs if the code doesn't clear automatically. The best way to reset a check engine light is to use a code scanner. However, if your vehicle was manufactured beforeyou can simply disconnect the battery to reset the light. Warning: Once the OBD system resets which occurs after a few drive cycles or a certain number of miles, depending on the vehiclethe light will come back on if the problem has not been fixed.

Warning: Erasing codes by disconnecting your vehicle's battery can also clear out the memory for your radio and other onboard components. One option is to turn the ignition on and off 3 times in a row. Then, drive your vehicle around and check to see if the light goes off. Press on the horn for 30 seconds to drain any remaining electricity, then wait 15 minutes before reconnecting the battery cables. If all else fails, purchase an OBD code scanner and plug it into the OBD port on your vehicle, which should be located under the steering column.

Turn on the scanner and wait for it to scan your vehicle for error codes. To learn how to reset a check engine light with a code scanner, read on! Did this summary help you? Yes No.

Log in Facebook Loading Google Loading Civic Loading No account yet? Create an account. We use cookies to make wikiHow great. By using our site, you agree to our cookie policy. As the COVID situation develops, our hearts ache as we think about all the people around the world that are affected by the pandemic Read morebut we are also encouraged by the stories of our readers finding help through our site.Polaris makes a line of ATVs that, like most vehicles, require regular oil changes.

Polaris suggests changing the oil every 1, miles or hours of driving, whichever comes first. If you are due for an oil change, the service light will come on. After you've changed the oil, reset the light to start the next service interval. Turn the key to the "Off" position and remove it from the ignition. Activate the parking break so the ATV does not roll. Shift the ATV gear into neutral with the shift stick. This gear is often labeled with an "N". Press the button labeled "Mode Overide".

This button is next to the "Engine Stop" switch on the left-hand handle bar.

how to reset check engine light on polaris ranger

Hold down the "Mode Override" button while turning on the vehicle. Turn the key to the "On" position to start the engine, then release the "Mode Override" button. Select the "Service Interval" choice from the menu on the control panel.

Press the "Mode Override" button until you see this option. Press the "Manual Override" button three times. This will cause the light to blink.

Hold down the "Manual Override" button until the light stops blinking and turns off. This resets the service light. This article was written by the It Still Runs team, copy edited and fact checked through a multi-point auditing system, in efforts to ensure our readers only receive the best information. To submit your questions or ideas, or to simply learn more about It Still Runs, contact us.

how to reset check engine light on polaris ranger

Step 1 Turn the key to the "Off" position and remove it from the ignition. Step 2 Press the button labeled "Mode Overide". Step 3 Select the "Service Interval" choice from the menu on the control panel. About the Author This article was written by the It Still Runs team, copy edited and fact checked through a multi-point auditing system, in efforts to ensure our readers only receive the best information.Access the oil dipstick and oil fill cap by tilting the rear cargo box. The crankcase drain plug is located on the bottom of the crankcase.

Access the drain plug through the skid plate access hole located directly under the crankcase. Clean the area around the crankcase drain plug. Use caution when performing this procedure.

Do not allow hot engine oil to come into contact with skin, as serious burns may result. Place a drain pan under the engine crankcase and remove the drain plug with a 6mm Allen socket.

Allow the oil to drain completely. Remove all cargo from the cargo box. Always remove all cargo from the cargo box before lifting the box to access the engine.

Using the 2. Using a clean dry cloth, clean the filter sealing surface on the engine crankcase. Lubricate the O-ring on the new oil filter with a film of fresh engine oil.

Check to make sure the O-ring is in good condition.

how to reset check engine light on polaris ranger

Install it to specification. The oil filter is part number Both oil change kits include the filter. Replace the sealing washer on the drain plug.

The sealing surface on the drain plug should be clean and free of burrs, nicks or scratches. The sealing washer is part number Reinstall the engine crankcase drain plug with the 6mm Allen socket. Torque the drain plug to 12 ft-lbs 16 Nm. Remove the oil fill cap. Fill the engine with the recommended engine oil.

The oil capacity is 2. Stop the engine and inspect it for oil leaks. Wait at least 15 seconds before removing the dipstick. Unlock the dipstick lever. Remove the dipstick and wipe it dry with a clean cloth. Reinstall the dipstick and push it into place. Do not lock the dipstick. Make certain the dipstick is inserted all the way into the dipstick tube to keep the depth of the dipstick consistent. Add the recommended oil as necessary to bring the oil level within the SAFE range on the dipstick.

Do not overfill. The service interval counter is programmed to 25 hours at the factory.The flashing service wrench icon on a Polaris Sportsman's speedometer can lead many riders to panic.

In most cases, this icon is triggered by the engine's hours of operation reaching a programmed interval, and it acts as a friendly reminder that your ATV is ready for a routine servicing.

Whether you perform the service yourself or leave the work to professionals, the wrench icon will continue to appear until it is manually reset. Press the "SELECT" button to scroll through the speedometer's menu functions until the remaining service hours are displayed. This will allow you to adjust the amount of engine operation hours before triggering the service wrench Icon. You may elect to turn the service feature off completely by selecting "OFF" in the menu.

Wait until the service hours display stops flashing, then turn the ignition switch off. The service wrench icon has now been reset. Wait until the service hours display stops flashing and turn the ignition switch off. This article was written by the It Still Runs team, copy edited and fact checked through a multi-point auditing system, in efforts to ensure our readers only receive the best information.

To submit your questions or ideas, or to simply learn more about It Still Runs, contact us. Step 1 Turn the ignition switch on. Do not start the motor at this time. Step 1 Turn the ignition switch on then off. Wait for a second period. Step 2 Lock the parking brake and place the ATV into neutral.

About the Author This article was written by the It Still Runs team, copy edited and fact checked through a multi-point auditing system, in efforts to ensure our readers only receive the best information.Forums New posts Search forums. What's new New posts New profile posts Latest activity. Members Current visitors New profile posts Search profile posts.

How to Reset a Polaris Service Light

Log in. Search Everywhere Threads This forum This thread. Search titles only. Search Advanced search…. Everywhere Threads This forum This thread. Search Advanced…. New posts. Search forums. Sidebar Sidebar.

My wife rides shotgun in the Polaris RZR 1000, Hold on honey!!!

JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding. Oct 19, 8 6 3 48 Chula Vista, Ca www.

I was going to look some more tonight. JoeyD23 utvunderground. Jan 9, 18, 1, 40 North County San Diego www. Have you tried unplugging your ECU? I called motoworld.Forums New posts Search forums. What's new New posts New profile posts Latest activity. Members Current visitors New profile posts Search profile posts.

Log in. Search Everywhere Threads This forum This thread. Search titles only. Search Advanced search…. Everywhere Threads This forum This thread. Search Advanced…. New posts. Search forums. Sidebar Sidebar. JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding. Oct 19, 8 6 3 48 Chula Vista, Ca www.

I was going to look some more tonight. JoeyD23 utvunderground. Jan 9, 18, 1, 40 North County San Diego www. Have you tried unplugging your ECU? I called motoworld. But i drove it in Low gear at rpm for about 20 seconds and it cleared the codes and EPS started working again. Reactions: Glamisfan. Show hidden low quality content. You must log in or register to reply here. Members online Pete. A loco oquintero Latest posts D.

how to reset check engine light on polaris ranger

General UTV Discussion. Desert Racing. Forum statistics Threads 17, MessagesMembers 11, Latest member vvoskuil. Share this page Share this page Share. Top Bottom.


Comments

Leave a Reply

Your email address will not be published. Required fields are marked *